Actuating elements for indexing plungers with remote actuation,...

go back

Products
- Operating parts | standard elements
  - Spring plungers, indexing plungers, ball lock pins
    - Indexing plunger
      - Indexing plungers, stainless steel with plastic mushroom grip and remote actuation
        Actuating elements for indexing plungers with remote actuation, with plastic mushroom grip and locknut

Item description/product images

DescriptionMaterial:Actuating element stainless steel.
Mushroom grip thermoplastic.Version:Mushroom grip thermoplastic, dark grey.
Plastic cover thermoplastic, in black, grey, red or yellow.Note for ordering:Indexing plungers with remote actuation and actuating element must be ordered separately.Note:The supplied screw nipple (Ø5 x 7 mm) can be used as an alternative to the actuating element to integrate a customised actuating element into the system.

Different lengths of the Bowden cable are available.
The Bowden cable can be shortened as required during installation to ensure an exact fit in the application concerned.

Corrosion protection is achieved by selecting a suitable material and surface treatment. The wire cable or cable sheath can be easily replaced if required.

Note the following points when installing Bowden cables:
The length of the free end of the cable can change due to layout angle, bend radius and load factors. Therefore, the length of the opposing bracket (cable sheath) must be adjusted using the enclosed set screw after the Bowden cable has been laid. The set screw is also used to set the tension in the Bowden cable system.
During installation, take particular care to ensure that the bend radius is not less than the minimum value, which in this case is R = 65 mm. A radius which is too small can lead to increased wear and higher friction.
Briefly bending less than the min. bending radius during installation should also be avoided, as this can damage the cable sheath. The sheath is also only designed to absorb compressive forces. If it is pulled too hard, the internal spiral will stretch and be permanently damaged.On request:Special versions.Accessory:Hex nuts K0700.
Mounting brackets K0638.
Spacer rings K0665.
Positioning bushes K1290.
Actuating elements K1502.12420.
Bowden cable K2116
Wire cables K2023.
Tension sleeves K2024.
End sleeves K2025.
Setscrews K2026.
Screw nipples K2027.
Supplied withActuating element with plastic cover.Drawing reference:

1) Indexing plunger
2) Bowden cable casing
3) Bowden cable
4) Adjusting screw
5) Actuating element
6) Screw nipple
7) Cover

Form B: non-lockout type, with locknut

Special features:

DownloadHere is all the information as a PDF datasheet:

Are you looking for CAD data? These can be found directly in the product table.

Datasheet K1502_BE Actuating elements for indexing plungers with remote actuation, with plastic mushroom grip and locknut

313 kB

Drawings

Item selection/filter

Order No.	Colour Cap	D Internal thread	D1	D2	L	L1	L2	L3	SW1	SW2	Price
K1502.12420	black grey RAL 7021	M6	M20x1,5	33	73	28	12	25	22	30	on request
K1502.124201	orange RAL 2004	M6	M20x1,5	33	73	28	12	25	22	30	on request
K1502.124202	signal green RAL 6032	M6	M20x1,5	33	73	28	12	25	22	30	on request
K1502.124203	blue RAL5017	M6	M20x1,5	33	73	28	12	25	22	30	on request
K1502.124205	light grey RAL 7035	M6	M20x1,5	33	73	28	12	25	22	30	on request
K1502.124206	traffic red RAL 3020	M6	M20x1,5	33	73	28	12	25	22	30	on request
K1502.124207	colza yellow RAL 1021	M6	M20x1,5	33	73	28	12	25	22	30	on request